The powerful DC fan can forcibly remove heat accumulated in the mixer system. Reduces mixer system temperature by approximately 10 degrees. Suppresses mixer system temperature increase due to heat generated by material. Realizes enhanced efficiency in repeated operations due to shortening of cooling down interval time. Feature Exhaust heat table ENs-10 is a product developed for THINKY MIXER ARE-310, ARE-250, and SR-500. Specification Unit Dimensions/ Unit weight H145×W310×D320（mm）Approx. 7kg Compatible models A type: ARE-310, SR-500 B type: ARE-250 read more

Containers and adapters are the key factors to achieve maximum performance!THINKY designs original containers and adapters for planetary centrifugal mixers. Feature THINKY provides the most suitable containers results in optimum material processing. Moreover, we consider material characteristics, customers’ issues, and operating environment,etc. to create the only one adapter for your material. Fine response and attentive service are our strengths as a pure play company. read more

Nano pulverizing of material at low temperatures Minimal (100mg) quantities can be pulverized in a short time. Pulverizing quantity minimum 100mg (10ml liquid) to maximum 10g. Pulverizing time 2-5 minutes. Provides standard recipes for pulverizing. Contamination is minimized in a closed container. Feature Nano Pulverizer NP-100 was designed with an optimized planetary centrifugal ratio to maximize the collision energy. NP-100 has strong centrifugal forces caused by rotation and revolution motion. The centrifugal forces add acceleration to the pulverizing media (zirconia balls) and strongly pulverize materials. Although dry-milling less than 3 micron pulverization is principally difficult, wet-milling enables nano pulverizing. Specification Unit Dimensions/ Unit weight H785×W625×D600（mm）Approx. 96kg Power Supply Voltage：Single phase,AC120V±10%,50/60HzConsumption power:At standby:55/53VA[50/60Hz]During standby operation:Max.1,400VA Option Zirconia containers enable pulverization of 10 ml material at minimum Volume of material 100mg - 10g *1 Maximum liquid volume 80ml Recommended container Pulverizer set（Zirconia)Media separation set(SUS) read more

The next generation ultrasonic mixer that　disperses nano-materials in a safe and reproducible manner Highly Reproducible Dispersion Pulverizing time 2-5 minutes. Unique Dispersion Technology (Patented) Water Temperature Control Using Cooling Unit Low Running Cost Contamination-free Feature PR-1 is designed to highly reproduce the dispersion of nano-materials such as CNTs, while operating safely by keeping the sample in an enclosed container. The dual-sonic technology (patented) rotates the container at a high speed while ultrasonic irradiates from the bottom and side of the ultrasonic bath. Rotating the container at an angle of 45℃ causes convection in the materials, and thus ultrasonic irradiates the entire sample. Specification Unit Dimensions/ Unit weight H400×W450×D380（mm）Approx. 25kg Max Processing Applox. 5ml Maximum Processing Volume 5ml Standard Container*2 *2：Contact us because the actual volume of mixing may vary depending on the containers, materials, and conditions. Test tube-shaped vial(capacity 5ml) Power Supply Voltage：Single phase,AC85V - 265V (47Hz - 63Hz)Consumption power:At standby:50VADuring standby operation:500VA(Excl. start time) Accessories 150ml SUS container   read more

Special purpose machine that can optimize temperature and viscosity preparations and dispersion and deaeration of solder paste at the same time Can immediately prepare cold stored solder paste without bringing it back to room temperature By optimizing the mixing recipe, viscosity preparation and temperature preparation for solder paste is easy. Removes large air bubbles in the paste, which are considered the cause of solder paste defects. Handles commercial 500g solder paste containers as is Restirs and redisperses solder paste that has been used Supports solder paste in syringes by using the optional adapter Feature Can prepare uniform viscosity in a short time for solder paste just taken from cold storage without bringing it back to room temperature. Metal particles with high specific gravity such as solder particles settle to the bottom of containers in cold storage and cause differences in material viscosity. The SR-500 regulates the viscosity of solder paste in a short time, with uniform viscosity from top to bottom. Also, because it can remove air bubbles thought to cause spattering of solder balls, it contributes to reducing the defect rate. Specification Unit Dimensions/ Unit weight H390 ×W300×D340（mm） Approx. 18kg Maximum Capacity*1 *1：Total mass to mount on the cup holder, including materials, containers, and adapters. 680g Standard Container*2 *2：Contact us because the actual volume of mixing may vary depending on the containers, materials, and conditions. 150 ml resin container Power Supply Voltage: Single-phaseAC 120 V ± 10 %, 50/60 HzPower consumption:Approx. 50 VA (standby)Max 900 VA (operation) Accessories Instruction Manual × 1,AC cable (including 3P adapter) × 1,150 ml container × 3,Adapter for HDPE 150 ml container × 1(including 1 O-ring)Silicon rubber sheet × 1,O-ring for fine adjustment × 11 metal fitting is attached to the unit rear to release the lid lock, in case of power failure. read more

Standard vacuum mixer enabling uniform mixing and elimination of submicron-level air bubbles. Simultaneous mixing, dispersion, and submicron-level air bubble elimination Deaeration of high-viscosity materials difficult to be processed by a centrifugal separator Reduced processing time and improved deareation performance compared to the atmospheric type mixer Centrifugal force of revolution prevents overflow of material during operation High-specific-weight materials such as fluorescent material can be evenly dispersed and deaerated without sedimentation (ARV-310LED) CE certified model is available Feature Combining vacuum pressure reduction function with rotation and revolution mixing for general purposes enables efficient elimination of submicron-level air bubbles. With rotation and revolution movement under vacuum pressure reduction, deareation of high-viscosity materials; which was considered difficult, can now be performed with excellent quality. The processing time can be further reduced compared to the atmospheric mixer. In terms of operation; the centrifugal force of revolution during the mixing process suppresses the material within the container, eliminating the need to keep an eye on the material so that it does not overflow, as is needed with static vacuum chambers. Specification Unit Dimensions/ Unit weight H450×W555×D645（mm）Approx. 90kg Maximum Capacity*1 *1：Total mass to mount on the cup holder, including materials, containers, and adapters. 310g Standard Container*2 *2：Contact us because the actual volume of mixing may vary depending on the containers, materials, and conditions. 300 ml resin container Power Supply Voltage: Single-phaseAC 100 V ± 10 %, 50/60 HzPower consumption:Approx. 50 VA (standby)Max 1200 VA (operation) Accessories Voltage: Single-phaseAC 100 V ± 10 %, 50/60 HzPower consumption:Approx. 50 VA (standby)Max 1200 VA (operation) read more